{"product_id":"syvecs-syv-wmi-water-methanol-injection-controller","title":"SYVECS SYV-WMI WATER\/METHANOL INJECTION CONTROLLER","description":"\u003ch4\u003e\u003cstrong\u003eDescription\u003c\/strong\u003e\u003c\/h4\u003e\u003cp\u003eThe Syvecs WMI standalone controller is a compact but very powerful unit for controlling a complete WMI electronics system, safely and correctly. It has been designed to integrate into any car easily via the use of CANbus communications, allowing users to receive critical engine data from OEM or aftermarket engine ecus with the use of just 2 wires (does not need a Syvecs Engine ECU). This data can then be linked into the WMI controller for use in strategies or monitoring systems to provide a modern based control system with safety in mind. Additional sensors can also be connected to the controller to provide more data to further add safety into the system, like a Level Sensor, Flow sensor and Pressure sensor. If CANbus is not supported on the installed vehicle then the WMI unit will also allow RPM and Injector Duty to be picked up from wires in the original engine loom.\u003c\/p\u003e\u003cp\u003eAdvanced users can also setup custom can transmit option with the powerful CANbus section to allow bits or bytes to be sent on the OEM CANbus to invoke ECU Lights, Torque Limits and more.\u003c\/p\u003e\u003cp\u003eThe WMI controller is fitted with four Half Bridges drivers which are capable of driving Low or High and able to handle a maximum of 15amps peak\/8amp continuously each. Pin Sharing is also available for the WMI Pump and Solenoid to handle double the current capabilities of a single pin.\u003c\/p\u003e\u003cp\u003eEach of the four H-Bridge Outputs is equipped with a current monitoring circuit which is used part of the limp protection strategies to ensure solenoids are connected correctly and not shorting. If the WMI Solenoid or Pump is driven and no current flow is detected it will immediately invoke a Limp flag which can warn the users via a LED Output, CAN message to a dash or torque limit to an engine ecu. The same goes for a short circuit in the wiring causing a over-current situation which will set a limp flag as well and shutdown the output for safety.\u003c\/p\u003e\u003cp\u003eThe four 0-5v analog inputs fitted on the controller can be used for external switches, sensors or trim pots via the Scal - Pin assignment setup which is fully flexible.\u003c\/p\u003e\u003cp\u003eFour PWM inputs are also fitted on the controller that can be used for Flow sensors, Rpm Signals and Injector Duty pickup.\u003c\/p\u003e\u003cp\u003eTwo CANbus interfaces are fitted on the WMI Controller which are flexible for transmitting any of the WMI parameters on the canbus. Receiving data is also possible from a Syvecs Ecu, OBD2 Protocol or a selection of supported OEM DataStream’s listed below:\u003c\/p\u003e\u003cp\u003eCurrently the following Cars are supported but check the Syvecs Forum for WMI firmware updates as more cars will be added.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eAudi Mk2 TTRS \/ RS3\u003c\/strong\u003e- Supports: Rpm, Tps, Pps, Torque Actual, Torque Demand, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAudi Mk3 TTRS \/ RS3 \/ S3\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Cal Selection (Drive Mode), Torque Actual, Torque Demand, ACT, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAudi R8 Gen1\u003c\/strong\u003e - Supports: Rpm, Tps, Pps, Torque Actual, Torque Demand, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAudi R8 Gen2\u003c\/strong\u003e - Supports: Rpm, Map, Tps, Pps, Cal Selection (DriveMode), Torque Actual, Torque Demand, ACT, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBMW E46\u003c\/strong\u003e - Supports: Rpm, Tps, Pps, Torque Actual, Torque Demand, ECT, EOT, BrakeP, Speeds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBMW E92\u003c\/strong\u003e - Supports: Rpm, Tps, Pps, Torque Actual, Torque Demand, ECT, EOT, Gear, BrakeP, Speeds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCorvette Z06\u003c\/strong\u003e - Supports: Rpm, Tps, Pps, Torque Actual, Torque Demand, ECT, BrakeP, Speeds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEvo X\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Cal Selection (SportMode), Torque Actual, Torque Demand, ACT, ECT, EOT, Gear, BrakeP, Speeds, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGT86\/BRZ\u003c\/strong\u003e- Supports: Rpm, Tps, Pps, Torque Actual, Torque Demand, ECT, EOT, Map1, BrakeP, Speeds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHonda FD2\/FN2\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Torque Actual, Torque Demand, ECT, BrakeP, Speeds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHonda FK2\/FK8\u003c\/strong\u003e- Supports: Rpm, Tps, Pps, Torque Actual, Torque Demand, ECT, EOT, Map1, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInfiniti Q60\u003c\/strong\u003e- Supports: Rpm, Tps, Pps, Cal Selection(SportMode),, Torque Actual, Torque Demand, ECT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLamborghini LP520\u003c\/strong\u003e- Supports: Rpm, Tps, Pps, Torque Actual, Torque Demand, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLamborghini LP560\u003c\/strong\u003e- Supports: Rpm, Tps, Pps, Torque Actual, Torque Demand, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLamborghini Huracan\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Cal Selection(SportMode), Torque Actual, Torque Demand, ACT, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLamborghini Aventador\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Cal Selection(SportMode), Torque Actual, Torque Demand, ACT, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMclaren 12C, 650S, 675, 570, 600, 720, 765, P1\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Cal Selection(ACTIVE SYSTEM),Torque Actual, Torque Demand, ECT, Gear, BrakeP, Speeds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMercedes Gen1, C63, E55\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Torque Actual, Torque Demand, ECT, Gear, BrakeP, Speeds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMercedes Gen2\u003c\/strong\u003e\u003cstrong\u003eC63, SLS\u003c\/strong\u003e- Supports: Rpm, Tps, Pps, Cal Selection(SportMode), Torque Actual, Torque Demand,ACT, ECT, EOT, Gear, BrakeP, Speeds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNissan 370Z\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Cal Selection(SportMode), Torque Actual, Torque Demand, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNissan Patrol Y61\u003c\/strong\u003e- Supports: Rpm, Tps, Pps, Torque Actual, Torque Demand, ECT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNissan Patrol Y62\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Torque Actual, Torque Demand, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNissan R35GTR\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Cal Selection (RMode), Torque Actual, Torque Demand, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePorsche 991 \/ 981 \/ GTS \/ GT2RS \/ GT3\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Cal Selection(SportMode), Torque Actual, Torque Demand, ACT, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePorsche 996\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Cal Selection(SportButton), Torque Actual, Torque Demand, ECT, EOT, Gear, BrakeP, Speeds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePorsche 997 \/ 987\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Cal Selection(SportButton), Torque Actual, Torque Demand, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSimos 18\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Cal Selection(DriveMode), Torque Actual, Torque Demand, ACT, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSyvecs S7 Fixed Stream\u003c\/strong\u003e- Supports: Rpm, Map, Lam1, FuelDuty, Tps, Pps, Cal Selection(CalSelect), Torque Actual, Torque Demand, ACT, ECT, EOT, Gear, BrakeP, Speeds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eToyota Yaris Gr, Corrola, LandCruiser 21+\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Cal Selection (AWDMode), Torque Actual, Torque Demand, ECT, EOT, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eToyota LandCruiser 2015 \/ Lexus LX570\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Torque Actual, Torque Demand, ACT, ECT, BrakeP, Speeds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVAG ME7\u003c\/strong\u003e- Supports: Rpm, Tps, Pps, Torque Actual, Torque Demand, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVAG ME9\u003c\/strong\u003e- Supports: Rpm, Tps, Pps, Torque Actual, Torque Demand, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVAG MED17\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Cal Selection(DriveMode), Torque Actual, Torque Demand, ACT, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVW Golf Mk5\/6 \/ TFSI \/ TSI, Cupra, Audi S3\u003c\/strong\u003e- Supports: Rpm, Tps, Pps, Torque Actual, Torque Demand, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVW Golf Mk7 MQB, Seat MQB, Audi MQB\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Cal Selection(DriveMode), Torque Actual, Torque Demand, ACT, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eECU Manufactures CAN supported:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMotec M1\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Cal Selection, Torque Actual, Torque Demand, ACT, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG, FuelDuty\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSyvecs Streams\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps, Cal Selection), Torque Actual, Torque Demand, ACT, ECT, EOT, Gear, BrakeP, Speeds, LatG, LongG, FuelDuty\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eECUMaster\u003c\/strong\u003e- Supports: Rpm, Map, Tps, Pps,ACT, FuelDuty\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eOBD2 Support\u003c\/strong\u003e- Supports: Rpm, Tps, Torque Actual, Torque Demand, Maf1, Map1, ACT , Lam1, Speed\u003c\/p\u003e\u003ch3\u003e\u003cstrong\u003eKey Features:\u003c\/strong\u003e\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eMonitoring of Pressure, Flow, Level, Lambda, Current and Temperatures\u003c\/li\u003e\n\u003cli\u003eLimp mode for all sensors and data\u003c\/li\u003e\n\u003cli\u003eCANbus support for Many OEM Cars and Ecu’s\u003c\/li\u003e\n\u003cli\u003eSet OEM Engine Check light when in Limp, only on supported models\u003c\/li\u003e\n\u003cli\u003eAnalogue support for Engine Speed, Air Temp, Manifold Pressure, Injector Duty if Canbus not available\u003c\/li\u003e\n\u003cli\u003eCurrent monitoring of each output with Limp protections\u003c\/li\u003e\n\u003cli\u003eClosed loop direct pump control\u003c\/li\u003e\n\u003cli\u003eDual Solenoid Control\u003c\/li\u003e\n\u003cli\u003eLive Map Switching from External Switch or OEM CANbus data\u003c\/li\u003e\n\u003cli\u003eSimple installation\u003c\/li\u003e\n\u003cli\u003eOutput Testing logic\u003c\/li\u003e\n\u003cli\u003eCustom Can Transmit to forward data to loggers\/ecu\u003c\/li\u003e\n\u003cli\u003eSupports high current demand with pin sharing technology\u003c\/li\u003e\n\u003cli\u003eFully configurable via Scal Software\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eOutputs\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e4 Half Bridge Outputs\u003c\/li\u003e\n\u003cli\u003e15Amp Peak (100ms) 8Amp Continuous\u003c\/li\u003e\n\u003cli\u003eCurrent Monitoring on each pin\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eInputs\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e4 Analogue or switch inputs (0-5V)\u003c\/li\u003e\n\u003cli\u003e4 Hall Effect \/ PWM inputs (0-5V)\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eInterfaces\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eUSB For Updates and Config\u003c\/li\u003e\n\u003cli\u003e2 x CAN 2.0B interface for communication with other controllers or logging systems\u003c\/li\u003e\n\u003cli\u003e1 x Kline Interface\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003ePower Supply\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e6 to 26V input voltage range\u003c\/li\u003e\n\u003cli\u003eIgnition Switch Logic with high current supply\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003ePhysical\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eIP67 Sealed in Automotive Spec -40c to 125c\u003c\/li\u003e\n\u003cli\u003e34 way Superseal 1.0\u003c\/li\u003e\n\u003cli\u003e88mm x 89mm x 40mm\u003c\/li\u003e\n\u003c\/ul\u003e         \u003cp\u003e \u003c\/p\u003e        \u003ch4\u003eCompatibility\u003c\/h4\u003e\u003cp\u003eFeel free to contact us at info@mlperformance.co.uk should you wish to double check!\u003c\/p\u003e        \u003cp\u003e \u003c\/p\u003e        \u003ch4\u003eCompatibility Check\u003c\/h4\u003e\u003cp\u003eTo ensure the part(s) you have ordered fits your vehicle, we run a compatibility check prior to dispatch. We can do this either using your registration number (UK) or the last 7 digits of your VIN. Simply enter your car details prior to checkout.\u003c\/p\u003e        \u003cp\u003e \u003c\/p\u003e        \u003ch4\u003ePart Number\u003c\/h4\u003e\u003cp\u003eSYVECS-SYV-WMI\u003c\/p\u003e        \u003cp\u003e \u003c\/p\u003e        \u003ch4\u003eMore Information\u003c\/h4\u003e\u003cp\u003e\u003cstrong\u003eManufactured by\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eSYVECS\u003c\/p\u003e","brand":"SYVECS","offers":[{"title":"Default Title","offer_id":48802639347937,"sku":"SYVECS-SYV-WMI","price":883.0,"currency_code":"GBP","in_stock":true}],"url":"https:\/\/mlperformanceusa.com\/products\/syvecs-syv-wmi-water-methanol-injection-controller","provider":"ML Performance USA","version":"1.0","type":"link"}